Titanium Temporary Abutment Round 0.5 for Implant H2.43

Titanium Temporary Abutment Round 0.5 for Implant H2.43

Intended Use

The Titanium Temporary Abutment Round 0.5 for Implant H2.43 is intended for the fabrication and support of screw-retained temporary and permanent bridge restorations on compatible Internal Hex H2.43 implants.

The abutment serves as a prosthetic interface between the implant and the restoration, providing stability, retention, and accurate positioning of multi-unit and bridge restorations.

The round prosthetic platform without an anti-rotation element is specifically designed for splinted restorations, bridge frameworks, and full-arch prosthetic applications.

Indications

The Titanium Temporary Abutment Round 0.5 for Implant H2.43 is indicated for:

- Temporary bridge restorations
- Permanent bridge restorations
- Screw-retained restorations
- Implant-supported bridges
- Multi-unit restorations
- Full-arch restorations
- CAD/CAM restorations
- Implant rehabilitation procedures

Clinical Procedure

Abutment Installation

1. Confirm successful implant placement or osseointegration according to the treatment protocol.
2. Remove the healing abutment or temporary restoration if present.
3. Clean and inspect the implant connection.
4. Position the Titanium Temporary Abutment Round 0.5 onto the Internal Hex H2.43 implant.
5. Verify complete seating of the abutment.
6. Insert the Titanium Screw (701203).
7. Tighten according to the implant system manufacturer's recommended torque values.

Restoration Fabrication

Laboratory Procedure

1. Verify correct positioning of the abutment on the master model.
2. Design the bridge framework according to the treatment plan.
3. Fabricate the restoration using conventional laboratory techniques or CAD/CAM technology.
4. Verify passive fit of the framework before finalization.
5. Finish and polish the restoration according to laboratory standards.

Temporary Restoration

1. Fabricate a provisional bridge restoration as required.
2. Verify fit, occlusion, and esthetics.
3. Adjust as necessary before delivery.

Restoration Delivery

Screw-Retained Restoration

1. Seat the bridge restoration onto the abutments.
2. Verify complete seating and passive fit.
3. Tighten prosthetic screws according to the recommended torque protocol.
4. Check restoration stability.
5. Verify occlusion and articulation.
6. Seal screw access channels using appropriate restorative materials.

Final Restoration Verification

Before treatment completion:

1. Verify complete seating of all abutments.
2. Confirm passive fit of the bridge framework.
3. Check restoration stability.
4. Verify occlusal contacts.
5. Confirm esthetics and soft tissue adaptation.
6. Obtain radiographic verification if indicated.

Removal Procedure

1. Remove restorative material from the screw access channels.
2. Loosen the prosthetic screws.
3. Remove the bridge restoration carefully.
4. Unscrew and remove the abutments if required.
5. Inspect all components before reuse or replacement.

Cleaning and Sterilization

- Remove all contaminants and manufacturing residues.
- Clean using approved medical device cleaning procedures.
- Rinse thoroughly with distilled or deionized water.
- Dry completely before sterilization.
- Sterilize before use in a steam autoclave at: 135°C (274°F)
- Follow validated sterilization procedures and local regulatory requirements.

Warnings and Precautions

- For professional dental use only.
- Use only with compatible Internal Hex H2.43 implant systems.
- Use only with Titanium Screw (701203).
- Verify complete seating before tightening.
- Follow recommended torque values.
- Do not use damaged or deformed components.
- Replace components showing signs of wear, deformation, or damage.
- Ensure passive fit of bridge restorations before final fixation.
- Intended primarily for splinted and bridge restorations where anti-rotation features are not required.

Storage

Store in a clean, dry environment protected from contamination, moisture, and mechanical damage.

CadCam