Titanium Standard Connector 2 mm for Angular Adapter

Titanium Standard Connector 2 mm for Angular Adapter

Intended Use

The Titanium Standard Connector 2 mm for Angular Adapter is intended for use as a prosthetic connection component in screw-retained implant restorations supported by two-piece angular adapter systems. The connector provides a secure interface between the angular adapter and the prosthetic restoration, facilitating accurate positioning and long-term fixation of implant-supported prostheses.

The component is designed for permanent restorations on fully osseointegrated dental implants.


Indications

The Titanium Standard Connector 2 mm is indicated for:

- Screw-retained implant restorations
- Full-arch implant rehabilitations
- Implant-supported bridges
- Fixed prosthetic restorations
- Angular correction restorations
- Multi-unit implant prosthetics
- CAD/CAM prosthetic frameworks

Compatible Components

The connector is intended for use with:

- Angular Adapter (630141, etc.)
- Plastic Sheath (687030)
- Titanium Base (690760, etc.)
- Titanium Prosthetic Screw (700229)
- Two-Piece Angular Adapter Systems (630141, etc.)
- 1.25 mm Hex Driver

Product Specifications

- Diameter: 4.0 mm
- Height: 2.0 mm
- Thread Type: M3.5 UNF
- Anti-Rotation Feature: None
- Material: Ti6Al4V Medical Titanium Alloy ASTM F136

Clinical Use

Prosthetic Preparation

- Verify compatibility of all prosthetic components.
- Inspect the Titanium Standard Connector for cleanliness and integrity.
- Confirm that the angular adapter (630141, etc.) is properly installed and secured.

Connector Installation

- Position the Titanium Standard Connector onto the Angular Adapter (630141, etc.).
- Align the connector with the internal thread of the angular adapter.
- Carefully screw the connector into the internal thread until fully seated.
- Verify complete and passive seating of the component.

Prosthetic Assembly

- Position the Plastic Sheath (687030) onto the connector according to the restorative protocol.
- Install the Titanium Base (690760, etc.) as required for the prosthetic design.
- Insert the Titanium Prosthetic Screw (700229).
- Tighten the screw using a compatible 1.25 mm hex driver.
- Apply the torque recommended by the prosthetic protocol and implant system manufacturer.
- Verify stability, passive fit, and correct prosthetic positioning.

Final Restoration

The Titanium Standard Connector may be used in:

- Full-arch restorations
- Implant-supported bridges
- Fixed screw-retained prostheses
- Multi-unit prosthetic restorations
- Angular correction restorations

After final installation:

- Verify occlusion
- Confirm passive fit
- Check prosthetic stability
- Ensure proper access channel sealing according to clinical protocol

Removal Procedure

- Remove the access channel filling material if present.
- Using a 1.25 mm hex driver, loosen the Titanium Prosthetic Screw (700229).
- Remove the prosthetic restoration.
- Carefully remove associated prosthetic components if required.
- Inspect all components before reuse or replacement.

Cleaning and Sterilization

- Remove all manufacturing residues and contaminants.
- Clean using approved medical instrument cleaning procedures.
- Rinse thoroughly with distilled or deionized water.
- Dry completely before sterilization.
- Sterilize before use in a steam autoclave: Temperature: 135°C (274°F)
- Follow validated sterilization protocols and local regulatory requirements.

Warnings and Precautions

- For professional dental use only.
- Use only with compatible angular adapters and prosthetic components.
- Verify passive fit before final fixation.
- Do not use damaged or deformed components.
- Follow recommended prosthetic tightening protocols.
- Ensure complete seating of all components before tightening.
- Components showing signs of wear, damage, or deformation must be replaced.

Storage

Store in a clean, dry environment protected from contamination, moisture, and mechanical damage.

CadCam