Titanium Base for Screw Multi-Unit M2

Titanium Base for Screw Multi-Unit M2

Intended Use

The Titanium Base for Screw Multi-Unit M2 is intended for the fabrication and fixation of custom screw-retained zirconia bridge restorations on osseointegrated implants restored with Esthetic Multi-Unit Connector Abutments Ø4.7 mm (611548, etc.).

The component serves as a prosthetic interface between the restoration and the multi-unit abutment, providing stable support for long-term implant-supported prosthetic rehabilitation.

The titanium base is designed for permanent screw-retained restorations and is suitable for multi-unit bridge restorations, full-arch restorations, and implant-supported prosthetic applications.

Indications

The Titanium Base for Screw Multi-Unit M2 is indicated for:

- Custom zirconia bridge restorations
- Screw-retained restorations
- Multi-unit restorations
- Implant-supported bridges
- Full-arch restorations
- Permanent prosthetic restorations
- CAD/CAM restorations
- Implant rehabilitation procedures

Laboratory Procedure

Restoration Fabrication

1. Verify compatibility of the Titanium Base with the Esthetic Multi-Unit Connector Abutment Ø4.7 mm (611548, etc.).
2. Inspect the component for cleanliness and integrity.
3. Design the custom zirconia bridge according to the treatment plan.
4. Fabricate the restoration using conventional laboratory techniques or CAD/CAM technology.
5. Bond or secure the zirconia bridge to the titanium base according to the selected restorative protocol.
6. Verify passive fit and proper prosthetic alignment before delivery.

Clinical Procedure

Titanium Base Installation

1. Confirm successful osseointegration of all supporting implants.
2. Verify that the Esthetic Multi-Unit Connector Abutments Ø4.7 mm (611548, etc.) are properly installed and secured.
3. Clean and inspect the abutment connections.
4. Position the Titanium Bases onto the Multi-Unit Abutments.
5. Verify complete seating of each titanium base.

Restoration Fixation

1. Seat the completed zirconia bridge restoration onto the Multi-Unit Abutments.
2. Insert the Titanium Screw M2 (700229).
3. Tighten the screws using a 1.25 mm Allen key according to the recommended prosthetic torque protocol.
4. Verify complete seating and stability of the restoration.
5. Check occlusion and adjust if necessary.
6. Seal the screw access channels according to standard restorative procedures.

Final Restoration Verification

Before completion of treatment:

1. Verify passive fit of the bridge restoration.
2. Confirm complete seating of all titanium bases.
3. Check restoration stability.
4. Verify proper occlusal contacts.
5. Confirm esthetics and soft tissue adaptation.

Removal Procedure

1. Remove restorative material from the screw access channels.
2. Loosen the Titanium Screws M2 (700229) using a 1.25 mm Allen key.
3. Remove the restoration carefully.
4. Inspect the titanium bases, abutments, and screws before reuse or replacement.

Cleaning and Sterilization

- Remove all contaminants and manufacturing residues.
- Clean using approved medical device cleaning procedures.
- Rinse thoroughly with distilled or deionized water.
- Dry completely before sterilization.
- Sterilize before use in a steam autoclave at: 135°C (274°F)
- Follow validated sterilization procedures and local regulatory requirements.

Warnings and Precautions

- For professional dental use only.
- Use only with compatible Esthetic Multi-Unit Connector Abutments Ø4.7 mm (611548, etc.).
- Use only with Titanium Screw M2 (700229).
- Verify complete seating before final tightening.
- Follow recommended torque values.
- Do not use damaged or deformed components.
- Components showing signs of wear, deformation, or damage must be replaced.
- Ensure passive fit of the restoration before final fixation.

Storage

Store in a clean, dry environment protected from contamination, moisture, and mechanical damage.

CadCam