Closed Clip Transfer for Short Implant H2.43

Closed Clip Transfer for Short Implant H2.43

General Information

Before using DMi products, the dentist, maxillofacial surgeon, or dental technician should carefully read all indications, contraindications, recommendations, warnings, and instructions for use, as well as all related product documentation including product descriptions, surgical and prosthetic protocols, instrument manuals, and catalogs.

DMi recommends participation in certified educational and training programs conducted by authorized DMi specialists. Additional product information and training resources are available through official DMi representatives and on the company website:
www.dmimplant.online

Product Description

The Closed Clip Transfer for Short Implant H2.43 is a precision impression component intended for closed tray implant impression procedures on short implants.

The transfer is fixed directly into the internal connection of the short implant without the use of a fixation screw. Stable positioning is achieved through a retention clip integrated into the transfer body.

The transfer consists of:

- Cylindrical transfer body
- Internal hexagon connection 2.43 mm
- Retention clip mechanism

The transfer hexagon engages the implant connection with a locking effect, while the retention clip secures the transfer inside the short implant through mechanical retention.

Manufactured from high-quality stainless steel for reliable dimensional accuracy and clinical durability.

The component is compatible with:

- UNIQUE Short Implant:
  Lengths: 5 mm, 6 mm, 7 mm
  Diameters: 3.75 mm, 4.2 mm, 5.0 mm, 6.0 mm

- PRIMA Short Implant:
  Lengths: 5 mm, 6 mm, 7 mm
  Diameters: 3.75 mm, 4.2 mm, 5.0 mm, 6.0 mm

Intended Use

The Closed Clip Transfer is intended for:

- Closed tray implant impression procedures
- Accurate transfer of short implant position from the oral cavity to the working model
- Implant-supported prosthetic rehabilitation
- Prosthetic workflows for osseointegrated short implants

Indications

The transfer is indicated for:

- Closed tray implant impressions
- Prosthetic restoration procedures on osseointegrated short implants
- Implant-supported restorative workflows
- Transfer of implant position to laboratory models

Contraindications

Do not use the product in cases of:

- Lack of implant osseointegration
- Allergy or hypersensitivity to metals
- Trismus of the masticatory muscles
- Limited mouth opening
- Increased gag reflex

Warnings

- The transfer is intended for single use only.
- The product is supplied non-sterile.
- Sterilization before clinical use is mandatory.
- Recommended sterilization method: autoclave sterilization at 135°C / 274°F.
- The clinician must be properly trained in implant impression techniques and use of the transfer system.
- Use only compatible implant systems and prosthetic components.

Precautions

- Verify compatibility with the implant system before use.
- Inspect the transfer for damage or deformation before use.
- Ensure proper seating of the transfer inside the implant connection.
- Follow standard implant prosthetic and infection control protocols.

Instructions for Clinical Use

1. Preparation
  - Remove the gingival former using a 1.27 mm hex driver.
  - Clean and dry the implant connection area.
2. Placement of the Transfer
  - Insert the Closed Clip Transfer (Ref. 901638) vertically into the internal hex connection of the short implant.
  - Ensure the 2.43 mm hex engages fully within the implant.
  - The retention clip secures the transfer inside the implant through mechanical retention.
3. Impression Procedure
  - Perform the impression using the closed tray “sandwich” technique (two-layer impression method).
Apply:
  - Low-viscosity impression material internally
  - High-viscosity impression material externally
  - Both materials may be inserted simultaneously.
  - Medium-viscosity impression material may also be used if clinically indicated.
4. Removal of the Impression
  - After polymerization of the impression material, remove the impression from the oral cavity together with the transfer.
5. Laboratory Procedure
  - Attach the laboratory analogue for Internal Hex 2.43 implant connection (Ref. 920038, etc.) to the transfer within the impression.
The resulting assembly consists of:
  - Impression
  - Transfer
  - Implant analogue
  - Send the completed assembly to the dental laboratory.
6. Model Fabrication
  - The dental technician applies gingival mask material around the implant area.
  - The impression is poured using dental stone (super plaster).
  - After setting, the impression and transfer are separated from the model.
  - The implant analogue remains embedded within the model for prosthetic fabrication.

Cleaning and Sterilization

The product must be sterilized before clinical use.

- Sterilization Parameters
- Autoclave sterilization
- Temperature: 135°C / 274°F

Follow validated sterilization procedures according to local regulations and clinical protocols.

Storage

- Store in a clean and dry environment.
- Protect from contamination, moisture, and mechanical damage.
- Avoid exposure to corrosive substances.

- DMI_IH2.1_IH2.43_exocad_V01.26.ZIP